• Solar charge controller

The MPPT VE.Can SmartSolar charger uses the latest and fastest technology to convert energy from a solar array into energy that optimally charges a battery bank.

The SmartSolar charge controller will even recharge a severely depleted battery. It can operate with a battery voltage as low as 0 Volts, provided the cells are not permanently sulphated or otherwise damaged.

• MPPT: Ultra Fast Maximum Power Point Tracking

The MPPT VE.Can SmartSolar charger connects to a PV array of 150 or 250 Volt Voc and will automatically detect and charge your 12, 24, or 48V battery bank with current ranging from 70 to 100A depending on the model.

The charge settings are fully programmable and can even be set up for different battery chemistries, like lead-acid, lithium and others.

• Control Your Charger Remotely

The MPPT VE.Can SmartSolar charger can be remotely controlled and configured over Bluetooth via the VictronConnect App. This allows device set-up, management, and at-a-glance information, such as battery voltage and current, PV voltage and current, and historical data.

• Daisy Chain Additional Units

The VE.Can SmartSolar charger is equipped with CAN bus ports. This allows for communication with additional VE.Can SmartSolar chargers. The additional units are simply “daisy-chained” to each other with a single RJ45 cable between the individual units.

When connected to each other, all individual VE.Can SmartSolar chargers, will synchronize their charge stages. They can also send their data, via a single cable, to a GX monitoring device.

• Remote Monitoring and Control

If the GX device is connected to the internet, the Victron Remote Management Portal (VRM) provides access to the full power of your solar charger(s).

For remote installations – even when there is no internet connection nearby – you may be able to monitor your MPPT by connecting the  GlobalLink 520.

• SmartSolar Control Display

The VE.Can SmartSolar charger is also equipped with a VE.Direct port like our other MPPT solar chargers. This port can be for single unit monitoring or for streetlight control. The remote on/off connector can be externally controlled by a third-party device like a lithium battery. An optional plug-in LCD display/control provides live-data, set-up and management, straight from the face of the device.

The Conext Automatic Generator Start (AGS) can automatically activate or stop a generator in response to changing power requirements. Excellent addition to an off-grid or backup power system, the AGS seamlessly connects to the Xanbus network and shares status information with all other devices on the network. It can monitor a set of system user-programmable parameters such as battery voltage, state of charge, or grid power and can activate the generator in response to any changes. The Conext AGS can also be configured remotely using the Insight energy management system to engage a generator and can assist an inverter/charger when output power demands are high.

Why Choose Conext Automatic Generator Start

Higher Return on Investment

• Integrate with an inverter/charger to maximize system power performance

Designed for Reliability

• Tested and qualified for harsh environmental conditions (HALT reliability testing)

Flexible

• Works with multiple Xanbus devices such as XW Pro, SW, MPPT 60-150, MPPT 80-600, MPPT 100-600, SCP, Insight
• User-programmable trigger settings to meet specific application needs such as battery voltage, exercise time, inverter AC power loads, SOC, and quiet time
• Supports manual start and stop operation modes

Easy to Service

• Access and troubleshoot AGS device events using the Insight or SCP
• Easily upgrade new firmware to the AGS using Insight

Easy to Install

• Wall mount
• RJ45 connections for Xanbus network cables

DEYE 18 kW Single Phase 3 MPPT Hybrid Inverter – SUN-12/14/16/18K-SG01LP1-EU-AM3-P
Single Phase Hybrid Inverter | 12-18 kW | 3 MPPT | LV Battery Supported

CU 202 is designed for monitoring and controlling SQFlex submersible pumps in solar applications.

The simple user interface and built-in Bluetooth module ensure easy installation and configuration. The Bluetooth connection to the Grundfos GO app offers extensive setup and monitoring options.

CU 202 is pre-configured for tank filling, the most used application, offering a plug-and-pump solution, which saves time on commissioning. For other applications, the controller provides several control modes, which can be easily selected and set through the Grundfos GO app. Grundfos GO makes the configuration easier and allows installers to set up high-performing systems.

CU 202 communicates with the pump through the power cable. This communication principle is called mains borne signaling or powerline communication and means that no additional cables are required to the pump.

Grundfos GO offers detailed information and logs that help the installer to find the root cause in failure situations. In addition, the controller can use Wi-Fi, GENIbus, or Modbus to monitor the system remotely either through Grundfos Connect or another SCADA system. Remote monitoring saves time when inspecting installations.

CU 202 is equipped with power and pump connections and offers 2 configurable inputs and outputs. Additionally, a backup battery can be added to the controller to maintain communication and measurements when solar power is insufficient.

The display of the controller shows:

The pump can be turned on and off through the display of the controller. The controller can display a read-out of the application-related data. It is also possible to adjust the setpoint. The LEDs on the display of the controller can be set to sleep mode, for example, to avoid attracting wildlife.

The following logs are available through Grundfos GO or remote monitoring:

CU 202 indicates warnings and alarms on the display of the controller. Additionally, the Grundfos GO app provides further information on these events including the recommended solutions.